CEREC Doctors

Discussion Boards

Daniel Kim Post a New Topic

Date Title
How could this happen?
By: Daniel Kim 17 Replies
Light walker laser hopefully helped me clean out this unusual canals on #18
By: Daniel Kim 5 Replies
HOLE IN ONE
By: Daniel Kim 5 Replies
Implant crown doesn't show contact patterson says it's 4.6 defect
By: Daniel Kim 6 Replies
EMax MT vs EMax Zircad Multi vs 3M Zirconia
By: Daniel Kim 21 Replies
3M Zirconia
By: Daniel Kim 14 Replies
How to restore Straumann wide neck implant
By: Daniel Kim 2 Replies
Is it easy to export ortho scans to stl file?
By: Daniel Kim 1 Reply
Can you stain Cerec blocks with Empress stain?
By: Daniel Kim 3 Replies
R2 Digital Lab
By: Daniel Kim 24 Replies
Is it normal?
By: Daniel Kim 3 Replies
Another Enamic IS abutment fracture
By: Daniel Kim
Has anyone used Blueskybio bridge blocks?
By: Daniel Kim 3 Replies
Do you make occlusal offset 0 for bio copies?
By: Daniel Kim 6 Replies
Enamic screw retained crown
By: Daniel Kim 1 Reply
My Biocopy crown is 2mm high
By: Daniel Kim 4 Replies
What cement do I use for Teilocad to Tibase
By: Daniel Kim 4 Replies
Do we have a Ti-base for Nobel Trilobe?
By: Daniel Kim 11 Replies
Can you convert finished crown case to implant crown case?
By: Daniel Kim 4 Replies
Is my Sirona scan post all the way down?
By: Daniel Kim 7 Replies
I think Cerec is more accurate than impressions
By: Daniel Kim 15 Replies
Vita Enamic IS abutment
By: Daniel Kim 8 Replies
Difference between Cerec Zirconia and InCoris TZI C
By: Daniel Kim 6 Replies
Is the color of Zirconia abutment normal looking?
By: Daniel Kim 16 Replies
please help! Can not advance after model axis
By: Daniel Kim 15 Replies
Today I sintered Katana in CS4 oven
By: Daniel Kim
How often you have to change water if you wet mill Zirconia?
By: Daniel Kim 4 Replies
ZirCad Crown #30
By: Daniel Kim 7 Replies
What does a 4 motor MCXL do that 2 motor can't
By: Daniel Kim 6 Replies
crowns are not touching but contact color is red
By: Daniel Kim 4 Replies
ZirCad crown before and after glazing and staining
By: Daniel Kim 2 Replies
Omnicam acting up
By: Daniel Kim 7 Replies
EMax ZirCad crown on #5
By: Daniel Kim 4 Replies
Abutment block choices
By: Daniel Kim 4 Replies
Not enough reduction?
By: Daniel Kim 17 Replies
Zirconia blocks
By: Daniel Kim 2 Replies
Glidewell's Bruxir Now needs no Sintering oven
By: Daniel Kim 2 Replies
If you are wet milling Zirconia, does it matter whether it’s speedfire or CS4?
By: Daniel Kim 12 Replies
3 unit Emax Bridge in P3
By: Daniel Kim 1 Reply
Is there a pink stain for Emax to simulate a gum color?
By: Daniel Kim 4 Replies
Life span of 25RZ and 10 finisfer burs
By: Daniel Kim 3 Replies
Can you use same Biocopy twice for 2 different cases?
By: Daniel Kim 2 Replies
Bonding an abutment and to a Tibase
By: Daniel Kim 1 Reply
Has anyone used DisiMax blocks?
By: Daniel Kim 4 Replies
What is the best way to make a screw hole in implant crowns
By: Daniel Kim 4 Replies
Is there a different wrench to install Shaper 25 RZ?
By: Daniel Kim 8 Replies
Using Enamic IS blocks as abutment blocks instead of Emax MO blocks
By: Daniel Kim 8 Replies
bonding Tibase to EMax abutment
By: Daniel Kim 3 Replies
In 4.4 I can't cut a hole in gingival mask and scan Scanbody in implant case
By: Daniel Kim 12 Replies
Can you use 5mm Tibase for 6mm 3i Certain implant?
By: Daniel Kim 6 Replies